[Other] SmartRG SR808ac
When I switched ISP's from Cogeco to mySignal[Frontier Networks] I purchased a SmartRG SR808ac modem from them [mySignal]. As normal I need access to the setup page to do static ip setup etc. What I...
View ArticleI want to use My new Spectrum modem with my old Frontier router?
I Just recently cancelled my Frontier Fios internet service. I signed up for Spectrum and they sent a D3.1 eMTA DOCSIS 3.1 Advanced Voice Modem. I bought the Frontier/(formally Verizon fios) Actiontec...
View ArticleDSL modem works one place, not another
I have two DSL modems: one new (ComTrend) and one old (17-year-old Westell 2200). Both modems work at my next door neighbor's house. At my house, only the new one works. I didn't change the...
View ArticleA little help needed with the speed of my cable modem and connectio
So far I haven't find any solution.... When I had Arris TG2942S cable modem and 250/20 mbits connection, the speed test showed always 250+/20+ mbits and A+/A(+)/A+ result. Then I got 1000/50 mbits...
View ArticleNew modem Technicolor
I just got ISP modem from Spectrum E31T2V1 Which I pretty sure dont use Puma6 chip set and is Broadcom? which very instant on I dont want Puma 6 Modem Is there IP login for this modem so i can see it...
View ArticleSaegcom F@ST3864AC router disconnecting
Hi, hopefully this is the right forum to post. If not please direct me. I am trying to diagnose what is going on with this router. It will sometimes work for long periods but at others will disconnect...
View Article[Other] Smart/RG SR516ac - How to unlock?
I got a used, locked Smart/RG SR516ac. I managed to get the username and password, and I was able to change the WAN, LAN and wireless settings as desired, and all works fine. The issue is that there is...
View ArticleSMC Network Tigerswitch 10/100/1000 various problems
Hi, I have a few of the aforementioned models of switch that I'm trying to restore to their factory settings. Most are behaving well, but a handful have varying issues. I'll leave a description of each...
View ArticleCopying from a Procurve using Putty
Hi all, A small dilemma, I'm trying to copy the CFA0/ contents from a Procurve 5406z1 to a USB, but I am repeatedly met with the help version of the cp command (cp -Copy file). I have 2 other identical...
View Article[Other] Overriding configured password on a SMC Tigerwitch
Hi all, I am attempting to restore a SMC 10/100/1000 tigerswitch to factory settings but the customer it previously came from has not removed their own login credentials. I cannot log into the switch...
View ArticleF5 6900
Hi all, When I attempt to boot up a F5 6900, I receive endlessly spamming messages of: HELO CLUI DRAM and other such acronyms. What can I do to overcome this? TIA
View ArticleAvocent DSR2010 Lost Password, reset procedure?
Hi all, Basically as the title suggests, I have this console and am trying to restore it to it's original settings. Unfortunately it has retained the login information from the prior owner. I am using...
View ArticleImperva Securesphere x1010 factory reset
Hi, Guides for the aforementioned unit suggest resetting passwords through the GUI, which I cannot access because I don't know what IP address has been set on my device, and the prior user's...
View ArticleF5 Password Recovery
Hi, After entering single-user mode on my F5 BIG IP 2000 (entering rd.break after the boot string), I cannot use the "mount" command. Typing help presents a list of options from the menu, but that is...
View ArticleF5 single-user password rejection
Hi all, I'm restoring a BIG IP 2000 unit and am met with a login failure when I boot into certain partitions using single-user or rd.break at the end of the string. The system notes : "set.12./:...
View Article[Other] Smart/RG SR516ac - How to unlock?
I got a used, locked Smart/RG SR516ac. I managed to get the username and password, and I was able to change the WAN, LAN and wireless settings as desired, and all works fine. The issue is that there is...
View ArticleMB8600 Modem - Lost an upstream channel
For some reason I can tell based on the event log reported by the modem, out of 4 upstrean channels , I only see 3 now. Midco tech checked and didn't find anything wrong. There are 4 channels seen on...
View ArticleMotorola MG8702 Modem - Configuring for Bridge Mode?
Hello, I have been trying to put the MG8702 modem into bridge mode by following the instructions here...
View Article[Other] Rasp Pi + Argon One case
I have the hw combo as in the subject . I have programmed the fan speeds for the temp range , using the shell script provided by Argon One. Is there any was to read the current temp and fan rpm ?
View Article[Other] Ubee E31U2V1 hardening and securing this internet cable router
I have it set to the maximum firewall settings such that all but my public IP is invisible to the world per Shields Up. What other configs can I use to harden this device to make my home network more...
View Article